The elastic membrane Izoplast Hydrolastic

Directory > Materials for waterproofing

The elastic membrane Izoplast Hydrolastic

Izoplast Hydrolastic two – component polymer-cement elastic waterproofing membrane.

1800
uah
x
компл.
=
1800 uah
Wholesale price 1530 uah from 20 компл.

For you, there will be a greater sense of the price of the proposition. Be affectionate, send a request and managers create an individual prorachunok for you.

CHECKOUT

Введите свои данные

Izoplast Hydrolastic – two-component polymer-cement elastic waterproofing membrane.

Applications:

  • Waterproofing buildings and structures for the protection of groundwater
  • Waterproofing horizontal and vertical surfaces
  • Waterproofing of swimming pools, bathrooms and shower rooms
  • Waterproofing drainage facilities, reservoirs and swimming pools
  • High resistance to negative water pressure

Advantages:

  • Good adhesion to all mineral substrates
  • Easy to apply by brush, ceiling brushes or by spray
  • Creates a seamless waterproofing coating
  • Covers cracks in concrete Foundation
  • Can be applied on screed, does not shrink
  • Contains no solvents, non-toxic and non-flammable
  • Can be used in residential areas and in potable water tanks
  • Creates a surface protection against salt water, chlorides and phosphates

Instructions for use:

The surface must be clean, smooth, solid, without any anti-adhesion substances such as dust, oil, dirt, rust, mold and detergents. If the concrete is delamination, the separated and the weak parts – they should be removed. If the floor or the wall of a crack or cavity, you want to seal, it should be repaired with appropriate repair solutions. Make sure that the plate or the concrete have a slope for proper drainage.

Before application the surface should be moistened. For dedusting of the surface and increase adhesion use primer solution Izoplast E Nano Power. Corners and abutting the half-wall should be beveled with a repair mortar.

Powder component must be thoroughly mixed to avoid lumps, then gradually add the liquid component to carry out the mixing with a low shear mixer. To the solution was ripened, after mixing you need to leave it for 5 minutes and then mix again for 1-2 minutes before applying.

The prepared solution should be applied in 2-3 layers with a roller, brushes or ceiling brushes. Maximum recommended thickness of one layer up to 2 mm. Each subsequent layer is applied after drying the previous one and perpendicular to each other.

The working time of the mixture is about 1 hour. The surface becomes water resistant after complete curing of the product. The material is carried out at a temperature from ambient 5°C to 35°C in the absence of strong wind and precipitation. Applied material should be protected from direct sunlight and precipitation.

The surface is ready for finishing work tile materials after 72 hours. The cured material is resistant to low temperatures down to -20°C.

Remarks / Restrictions:

Observe safety precautions and labour protection during execution of works. Observe the precautions. Use protective gloves, clothing, glasses. In case of contact with eyes, rinse with plenty of water and seek medical advice.

Composition

A (grey powder); B (polymer emulsion)

Color mixture

Grey

Packaging

A B set 33 kg

Shelf life

12 months in unopened original packaging

Drying time

≥ 6 hours

The interval between coats

≥ 6 hours

Consumption

3.5 kg/m2 for layer thickness of 2 mm

5.5 kg/m2 for a layer thickness of 4 mm.

Water resistant using

≥ 6 hours

Adhesion

≥ 0,5 N/mm2

The overlap of the cracks

> 2 mm

Application temperature

from 5 °C to 35 °C

Product publications

Waterproofing of the bathroom under the tile
Waterproofing of the bathroom under the tile

To perform internal high-quality waterproofing, insulating moisture-repellent materials are used.

Read article
Waterproofing outdoor balconies and terraces
Waterproofing outdoor balconies and terraces

Before you proceed with waterproofing work, thoroughly clean the concrete Foundation of dirt, dust, oils, loose particles and other materials.

Read article