Tile adhesive Teknofay Plus C1TE

Directory > Adhesives and sealants

Tile adhesive Teknofay Plus C1TE

Adhesive for high-strength tiles, reinforced with polymer.

282
uah
x
bag
=
282 uah
Wholesale price 239.7 uah from 10 bag

For you, there will be a greater sense of the price of the proposition. Be affectionate, send a request and managers create an individual prorachunok for you.

CHECKOUT

Enter your name and phone number

Teknofay Plus glue for ceramic and clinker tiles, mosaics, natural stone of class C1TE, on a cement basis, reinforced with polymer fibers.

Application areas:

  • For laying tile materials on horizontal and vertical surfaces
  • For gluing tiles of small and medium sizes
  • For gluing mosaic, natural stone, ceramic and clinker tiles
  •  For indoor and outdoor use

Features and benefits:

  • Long working time with the mixture
  • One-component, easy to mix
  • Does not slip on vertical surfaces
  • It does not contain solvents and has no smell
  • It has a high degree of adhesion to the surface

Instructions for use:

Surface preparation

The application surface must be cleaned of materials that prevent adhesion, such as dust, oil, resins and detergent. Weak parts of the surface should be dismantled. Chips, potholes and holes on the surface should be repaired with the help of appropriate Teknorep repair compositions. Before starting work, the surface should be cleaned with compressed air.

Mixing of the adhesive solution

To mix the adhesive solution, it is necessary to add a dry mixture to clean water (in the proportion of 1 kg of the mixture per 1 liter of water). Mixing is carried out using an electric mixer at low speeds (500-600 rpm) for 3 minutes. Let the solution stand for 5 minutes, then mix again until a homogeneous mass is obtained.     

Application and gluing

It is necessary to apply glue to the tile with the flat part of the spatula, and then hold the toothed side on it in one direction, then press it tightly to the gluing surface. The contact area of the tile with the surface must be at least 80%.

Gluing and leveling of ceramic tiles must be carried out within 30 minutes after applying the glue.

Notes/restrictions on use:

  • Do not add foreign substances to the mixture.
  • For better adhesion of the glue to the surface, it is necessary to make notches on it
  • May cause irritation if it comes into contact with the skin.
  • The equipment used should be washed with warm water and detergent immediately after application. After the glue has completely cured, it will be possible to clean the equipment only by mechanical means.
  • When working with the material, use basic protective equipment-gloves, glasses, protective masks. In case of contact with the eyes, rinse immediately with warm water and consult a doctor
  • After application, the surface must be protected from direct sunlight, precipitation, negative and high ambient temperatures (below 5°C and above 35°C).

Name

Value

Colour

White, Grey

Packaging

25 kg craft bag

Storage conditions

12 months in a dry environment in the closed original packaging

The ratio of water to dry mixture

7.0-7.5 l / 25 kg

Lifetime of the closed mixture

6 hours

Expenditure

3-5 kg/m2

Pedestrian loads

24 hours

Adhesion

≥ 0.5 N/mm2

Sliding

≤ 0.5 mm

Application thickness

≥ 0.5 mm

Mashing of seams

24 hours

Application temperature

( 5 °C) – ( 35 °C)

Operating temperature

(-40 °C) – ( 80 °C)

Shear strength of the clutch

- initial value (after 28 days)

≥0.5 N/mm2

- after exposure to heat

≥0.5 N/mm2

- after immersion in water

≥0.5 N/mm2

- after exposure to elevated temperatures

≥0.5 N/mm2

- after the freezing/thawing cycle

≥0.5 N/mm2