Concrete hardener quartz Teknoser 100

Directory > The materials for industrial floors

Concrete hardener quartz Teknoser 100

Hardener to fresh concrete surfaces, which includes sorted quartz sand.

288 uah
Wholesale price 244.8 uah from 10 bag

For you, there will be a greater sense of the price of the proposition. Be affectionate, send a request and managers create an individual prorachunok for you.


Введите свои данные

Teknoser 100 is a hardener for fresh concrete surfaces, which includes sorted quartz sand, hydraulic binder and special chemical additives. Increases the strength properties of the concrete surface by 1.5 times, gives the necessary decorative appearance of the surface.

Scope of application

  • For industrial floors with light and medium intensity of operation.
  • For stores and department stores.
  • Underground passages of metro stations, covered parking lots.
  • Production shops, warehouses, factories.
  • Shopping centers with heavy traffic, industrial buildings, gas stations, aircraft hangars.


Features and Benefits

  • Eliminates the formation of dust from the coated surfaces.
  • Excellent resistance to mechanical shocks.
  • Excellent resistance to coating wear.
  • Creates a strong, smooth and non-slip frost-resistant surface.
  • Increases the impermeability of concrete, increases the resistance to penetration of oils, lubricants, etc.


Instructions for use

Before applying TEKNOSER 100, the appropriate concrete hardness must be achieved, otherwise cracks may appear in the concrete.

TEKNOSER 100 is applied by the "dry-on-wet" method, which means that the hardeners must be applied to non-hardened concrete(approximately 5-6 hours after pouring) for better adhesion of the materials. Topping crumbles in an even layer at the rate of 2-4 kg / m2 and does not require additional watering, since the mixture will independently absorb the necessary amount of water from the concrete. After the hardener absorbs moisture and darkens, it is necessary to treat the coating with a grout machine, paying special attention to the corners and edges of the surface. Then it is necessary to re-fill with the calculation of 2-4 kg/m2 and re-rub the surface in the same way. Depending on the expected load force on the floor, the consumption of the dry mixture may vary.

Application Notes / Restrictions

  • To get the highest quality coating, you need to calculate the optimal time for application.
  • Avoid use in windy, extremely cold and rainy weather.
  • The application of the surface hardener should not be carried out in very windy or dry conditions.
  • Surface hardeners may change color depending on the type of concrete surface.
  • To ensure uniformity and continuity of color, the process of laying the floor should be as protected from environmental influences as possible.
  • Do not add fly ash to the concrete mix, as it accumulates in the upper layer of the slab, which leads to dust release of the floor covering or peeling of the hardener.
  • Do not add water to the concrete mix to increase its workability. This reduces the strength of the concrete and increases the chemical and physical shrinkage, resulting in uncontrolled scratches and cracks.
  • The product may cause irritation if it comes into contact with the skin. Wear protective gloves and safety glasses. In case of contact with eyes, rinse immediately with plenty of water and seek medical attention.


Available in grey, red, green

Shelf life

12 months in dry environment in unopened container


25 kg bag


4-8 kg/m2

Application temperature

5 °C - 30 °C

Bending resistance

9 N/mm2

Resistance to compression

70 N/mm2

Abrasion resistance (Taber method)

<4 g (H22, 1000 g, 1000 kr.)



Product publications

What kind of varnish to cover the concrete hardener
What kind of varnish to cover the concrete hardener

Teknocila 300 is a fast-drying one-component varnish based on organic solvents, which helps to protect concrete surfaces and extend their service life.

Read article
Concrete hardener quartz Teknoser 100

Other products